"cx complaint is the unit shaking a lot during spin. unit is on a tile floor and has turned away from the dryer thats beside it. cx had video of unit shaking during spin. i found no saved codes. shipping bolts have been removed. i ran service cycle. no issues. removed front of unit and inspected. no issues with suspension. called techline to document, they had me check that unit was level and pedistal was square, all feet contacting floor. adivsed issue is with cycle/load in unit. unit is working as designed."

S38253 CX complaint FRIDGE water leaks from ice built up on FC floor. Cleared all ice. Replace dran tube with Ptrap. Test water drain is good > JJ

"CX complaint bake not working.Removed oven bottom, tested igniter, amp draw was 2.5A. Replaced igniter using pre id part and ran a 350F bake cycle. The oven preheated and worked as designed."

"Cx complaint enamel pealing off the drum and getting on the clothes.Inspected drum, confirmed complaint. Ordering drum W10899578; ordrng 1 W10899578 (drum) and 1 look (look)"

"Installed gear case, also used cam-kit from truck stock to complete the repair. Calibrated and tested unit, working as designed.; ordrng 1 W10721967 (drive pulley jt vs) and 1 LOOK (LOOK), used 1 W10721967 (DRIVE-PULLEY) from stock"

"cx complaint received notice saying unit needs service. inspected unit and verified complaint. serial# in range of service pointer for heater replacement. asked if unit has leaked, cx said he not sure and showed me some water damage in cabinet under sink, pic saved. doesnt seem like its from dishwasher. pulled unit out and can see some water stains on cutout floor. noticed a bunch of streaks on back wall of cutout, pics saved. no signs unit has leaked from heater. replaced heater and tested. no leaks from unit at this time. advised cx it seems the windows may be leaking but advised him to call a handy man to find cause of water damage since it doesnt appear to be from dishwasher. cx understands. unit is now working properly"

"CX complant. Lights out in fridge. Prior diagnosis found lights out in fridge. Installed 4 leds and now all lights burning bright , Job completed, RB"

went to install support opened package found ui for fridge in package reordering one on UM right glide holding basket correctly top shelf bowed; ordrng 1 w10794550 (support) and 1 W11084821 (frame)

"CX complaint randomly oven doesn't turn off, even if the display says is off. Sometimes the oven turns off by itself. Ran test mode, found F6E4 (old code from 10/9/21). Called tech line, spoke to Bruce (sr # 7735154704), he advised to connect the unit to wifi and get the softwarte update, and if this doesn't work, to replace the console. Worked with the cx, connected the unit to wifi and go updates. Cx is monitorein the situation. Quoted console replacement just in case: $550.59 with $110 labor for console W11297728 replacement. Called Whirlpool Safety and documented ( sr # 7735071924); ordrng 1 W11297728 (console)"

CX complaint unit opening by it self. I found the unit is cooling and freezing and doors are closing and feel tight.CX stated that the unit when is not cooling the door pops open.checked level & is unlevel towards the front just where door swings went to shim front wheels & CX refuse this states duct tape will hold door explained that gravity & floor unlevelness will cause doors to open he will get baby latches to fix issue

CX comliant was that the unti shuts down mid cycle. I found that the the console was not connected to the control securely causing the Display to shut off and turn on. I securly seated the harness and unit test good.; ordrng 1 LOOK (LOOK)

"replaced valve and fill tube. cycled icemaker to test unit. no unusual buzzing noise now. tested water dispensing also, no noise. unit is now working properly"

Customer complaint is the unit is not cooling. Inspected unit I found that I could barely pull unit out of the cabinetry area due to the two bolts holding the base plate have been removed in the base plate getting caught on a tile where the unit was sitting. I ended up just putting two bolts in the area to pick the base plate up so it wasn't dragging on the ground. I then remove the cover and hook my watt meter up in place. My watt meter read 42 watts. I noticed the dryer that was on the unit is the factory original dryer. And when the compressor was replaced both times the dryer was never replaced ever.The dryer was cold to the touch I cut the cap tube off from the dryer nothing came out from the dryer I then cut the dryer off from the loop going through the drain pan. I still had no refrigerant coming from unit or pressure. I cut the Yoda loop from the cabinet to the drain pan heater tubing and had refrigerant and brown / black oil coming from the Yoda loop out of the cabinet. I then isolated the system from the condenser through the yodaloo and hooked up nitrogen and try to flush Yoda loop but was unsuccessful. I still had black oil slash debris coming from Yoda loop and condenser. I tried to flush through the cap tube out of the low side line before the compressor and had three rags of oil. I waited on the phone with tech line while trying to flush the system out with nitrogen at 140 psi. Eventually tech line answered and I explained what I was having an issue with. Tech line stated the unit is has a burnout and that this can not be repaired and gave me file number. I left file number with customer

i fpound the harness of the drain pump reset in place now drains and runs fine checksok

Replaced the rear right and rear left burners. Tested unit and it is now working properly. Job is complete

S38253 CX complaint FRIDGE water leaks from ice built up on FC floor. Cleared all ice. Replace dran tube with Ptrap. Test water drain is good > JJ

"cx complaint knob not gripping timer and timer hard to turn,found meatal insert of knob missing, found shaft of timer worn, ordering timer and knob...knob<30days; ordrng 1 W11566735 (timer) and 1 W11328381 (knob) and 1 WP688805 (clip)"

I installed the ordered part and tested the unit for the cx. The unit is working as designed.

"CX complant, Center burner dosent ignite. Inspected unit and found after milk was boiled over on center burner , Center burner now fails to ignite. . Cleaned orrifaces from spilled milk with a straight pin and tested unit . All burners now igniting and working as designed, Job completed, RB"

"cx complaint of unit not turning on at all,checked unit to find board being unreponsive at all replaced control board tested and calibrated unit works as designed"

Customer complaint is the unit is not cooling. Inspected unit I found that I could barely pull unit out of the cabinetry area due to the two bolts holding the base plate have been removed in the base plate getting caught on a tile where the unit was sitting. I ended up just putting two bolts in the area to pick the base plate up so it wasn't dragging on the ground. I then remove the cover and hook my watt meter up in place. My watt meter read 42 watts. I noticed the dryer that was on the unit is the factory original dryer. And when the compressor was replaced both times the dryer was never replaced ever.The dryer was cold to the touch I cut the cap tube off from the dryer nothing came out from the dryer I then cut the dryer off from the loop going through the drain pan. I still had no refrigerant coming from unit or pressure. I cut the Yoda loop from the cabinet to the drain pan heater tubing and had refrigerant and brown / black oil coming from the Yoda loop out of the cabinet. I then isolated the system from the condenser through the yodaloo and hooked up nitrogen and try to flush Yoda loop but was unsuccessful. I still had black oil slash debris coming from Yoda loop and condenser. I tried to flush through the cap tube out of the low side line before the compressor and had three rags of oil. I waited on the phone with tech line while trying to flush the system out with nitrogen at 140 psi. Eventually tech line answered and I explained what I was having an issue with. Tech line stated the unit is has a burnout and that this can not be repaired and gave me file number. I left file number with customerFile

"Customer complaint is that the unit is not powering on. Confirmed no response from the console. Found 1VAc from L1 to neutral at the control. Found the same result at the junction box. L1 to ground has 122.1VAc. Neutral to ground has 118VAc. Customer needs an electrician. Possible control is damaged by miswire, but will not know until power is corrected."

"replaced gearcase, slider, washplate and lid latch. installed lid latch that was shipped to the cx, sending back one that came with me. ran calibration and autotest. unit is now working properly"

"cx complaint, light out if FC. replaced parts per pre id. tested unit, unit working as designed. job is complete."

SR// 7735158211. Installed new control and same thing. I called techline and they told me to replace the same parts that i already replaced.; ordrng 1 W11342846 (Control) and 1 W11590866 (Sensor) and 1 W10844417 (harns-wire)

"cx complaint not washing dishes, found no errors, found no water entering unit, found valve buzzing, found good pressure to valve, replaced valve from ruck stock, tested all ops ok.... costco 2 year warranty..reorder for truck stock; ordrng 1 W11175771 (valve-inlt RL VS), used 1 W11175771 (valve RL VS) from stock"

replaced parts now checks good

Cx complaint unit is not working properly inspected unit removed and replaced the ice bin tested unit now functions normally

Cx stated PF failure inspected tested and verified cx complaint found control and console defective ordering console and control cannot reached at this time due to SO parts. ; ordrng 1 W11478519 (Console) and 1 W11557935 (Control)

cx complaint unit not cooling well. found both sections around 50 degrees. reclaimed high side to barely any r134. opened low side and it all came out of there. unit has a clog. put new drier and coupler on and flushed system with nitrogen. big puff of compressor oil and r134 came out. vacc unit and filled to 4.3 oz. unit is now cooling good. job completed.

"upon arrival cx said unit seems to be working after replacing control and valve but still has grinding noise. replaced gearcase, slider, clutch and agitator. ran calibration and autotest. no noises. unit is now working properly"

Inspected the unit. Found that the cx is saying that the Freezer has Frost. Checked the Freezer. No Frost. I then checked the Freezer Evaporator Section no Frost. Cx is saying Items in the Freezer Section had frosted over. Asked the cx if she left the door open. Cx started to get real get really aggressive because I asked this questions. Nothing is wrong with the unit.( I advised that the cx doesn't over load the Freezer Section.) (Please see Sd Pictures if any questions. )

"Cx complaint unit is not working. Arrived and found unit showing F2E1 error stuck/shorted key. Powered off and checked for loose connectors J4, J5, J6, J7. Connectors were fully inserted, reassembled and powered on unit. F2E1 error still displaying. Unit needs console replaced. Checked Whirlpool service parts portal, part is temporarily out of stock. Quoted cx cost of full repair, cx declined to go forward with repair."

Cx complaint is thumping noise coming from unit. inspected and verified complaint. found change inside the washplate. removed change and checked unit for error codes. no codes were found. ran a test cycle can unit completed cycle without issues. thumping sound was the water and drain hoses hitting the back of the unit. unit is working as designed. job complete

i fpound the harness of the drain pump reset in place now drains and runs fine checksok

GOT HERE went to install parts & found that exisitng fill tube not coming out after trying for more than 1hr will need door CX WANTS A REFUND FOR EVERYTHING WE CAN REFUND EVERYTHING BUT $165 FOR BOTH VISITS STATES IT WAS OK refund $271.68; ordrng 1 LW10397059 (dor-fip ms)

Installed new parts. Unit is back to normal operations.

replaced parts and cleared out drain hole.unit is now good

CX complaint unit not working ordering lid lock.; ordrng 1 W11394572 (Lid lock)

Cx complaint unit leaving clothes soaked at the end of the cycle. Was able to access unit and found it bouncing around empty. Checked suspension leveled unit and calibrated and unit is now operating as designed no further work needed

Per previous diag I was able to access and replace the door hinges. I then verified that the door is closing properly. Unit is now functioning as intended. Job complete

"Replaced Gearcase. rotor,stator,clutch,slider,screws unit calibrated and tested unit is working properly."

Customer complaint is that they have to run two 70 minute cycles to dry the clothes. Unit tested and the element is turning on and cycling properly. Checked air flow out of the unit to outside and found the exhaust heavily clogged on the outside of the house. Customer needs to have their vents cleaned. Unit is working properly.

Cx stated unit tub is leaking and not washing inspected tested and verified cx complaint found tub defective and separating from drum. Ordering drum bellow clamps and shock absorbers just in case will need a second tech for repair cannot reached due to SO part. ; ordrng 1 W11287253 (Tub) and 1 W11314648 (Bellow) and 1 W11314649 (Clamp) and 1 W11266654 (Clamp) and 1 W11316766 (Shock absorber) and 1 LOOK (LOOK)

Cx stated unit not cooling when on recommended level for freezer. Tested inspected but cannot verify cx complaint unit is working as designed. Job complete.; used 1 LOOK (LOOK) from stock

"cx complaint of unit not cooling ,checked to find little to no frost pattern on either evaps,called LR spoke with him and confrimed seal system was advise to order the parts,cx did not wish for a est at this time charging service call"

replaced door and checked over unit with cx. he said everything works great. got water out door and advised he should start to see ice in the next few hours and unit checks. job complete.

"Cx complaint enamel pealing off the drum and getting on the clothes.Inspected drum, confirmed complaint. Ordering drum W10899578; ordrng 1 W10899578 (drum) and 1 look (look)"

cx complaint unit not working properly checked unit to find no error codes ran test cycle completed all steps checked for error codes again no error codes present looked under unit to find no oil leaking from gearcase and belt is not slipping all connections are good unit is working as designed

"CX complaint: not tumbling. Tested and verified compklaint. I found the belt was broken but the suppoirt rollers and pulley wheel were all easily spinning. Replaced belt, tested unit and it is now working properly. Job is complete"

Cx complaint is unit freezing product in the RC. inspected and verified complaint. cx has fresh produce like lettuce and liquids on the top shelf near the cold air coming from the diffuser. tested diffueser and thermistor and the are reading and working properly. cx also stated doors were uneven. leveled doors to the cx's satisfaction. informed cx on proper placements of items on the top shelf. unit is working as designed. job complete

"Installed the User Interface, Evap cover & Door Switch. Tested the unit. Unit is starting to Cool. Unit is working as Designed. ( Any questions please check Sd Pictures.)"

"replaced control and owi. tested unit, no leaks but wash motor not running. skipped thru test cycle to get to heating and unit is heating. noticed previous tech had f4e3 error stored which is wash motor not running not failed owi. can hear wash motor try to run and diverter moving, but no water coming out. ordering wash motor, in stock @tribles. scheduled return visit for 12/13, please place cx on cancellation list; ordrng 1 W11087376 (wash motor) and 1 LOOK (LOOK)"

applied liner repair as per the instructions provided with the kit. took pics of final result to attach to file. also installed the shelf support as per previous tech. unit now checks good.

Inspected the unit. Found that the cx has gotten a letter stating that there is a Service Pointer on the Dishwasher Heater Element. Checked the Heater Element. Heater Element has the Black Coupler Bushings. Installed new Heater Element. Tested the unit. No leaks. Unit is working as Designed. Called Whirlpool safety Team Ref # 7735122184. Cx has Damages done to the house. Per Whirlpool Safety Team they will send a Damages sheet and contact the cx. ( Technical service pointer W11540964 - Special Project S17304. )

GOT HERE control board was on already same condition overfrost called TL explained all I have done checked resistance again of sensors TL states that control is the issue againACCORDING TO TL PART # NEEDS TO BE SEND TO A PARTS RESEARCH TEAM TO SEE IF THERE'S A DIFFERENT PART # SINCE WE CAN ONLY CHOOSE PART FROM A PREVIOUS ENGINEERING CODE let CX know SR#7734795995; ordrng 1 W11203924 (contrl-box CX complaint need to have it research) and 1 LOOK (LOOK)

SR// 7735158211. Installed new control and same thing. I called techline and they told me to replace the same parts that i already replaced.; ordrng 1 W11342846 (Control) and 1 W11590866 (Sensor) and 1 W10844417 (harns-wire)

"Per the previouse tech, I was able to access and replace the control board. I foun d the unit tobe opperating as designed. CX paid in full on 11/8; ordrng 1 LOOK (LOOK)"

per notes installed console tested unit repsonding

"Confirmed cx complaint unit not draining. Found drain pump receiving power but not draining properly. Installed pre-id'd part, tested unit, unit working as designed."

Cx complained of no cooling. Removed frost and installed new control and set to factory settings. Checked control to see if it had one bar code (good) or 2 bar codes (bad) and it has one. Spoke with tech support about the heater and it is in range. Job complete.

Cx stated unit not spinning inspected tested and verified cx complaint found drive hub defective causing tub to wobble. Tried installing part from pre-id parts but found wash plate needs to be cut out in order to complete repair. Gave cx quote for repair cx accepted quote and paid in full by CC ordering wash plate to complete repair. Cannot resched due to SO part. ; ordrng 1 W10902814 (Wash plate)

cx complaint detergent not desolving checked unit found f7e1 no heat code motor not turning in diagnostics verified 120vac from control to motor motor not turning also found worn gears on spray arm all parts in stock; ordrng 1 W10860176 (arm-spray) and 1 W10861526 (pump&motor)

"replaced console and u.i, tested, unit working as designed."

"came out to resolve the issue with the unit. disassembled the unit as needed. replaced all parts and tested the ice maker, thermistor, valve, etc. all working as designed. advsied cx to monitor the unit and if any issues persists to give the poffice a call.. cx agreed."

"CX complant. Water dripping on gasket Inspected unit and found water sitting on freezer gasket. Found mullion heater sensor on , TTurned off mullion strip heater sensor so heater stays on all the time. Job completed, Gaskets are all sealing good. And no cracks. RB"

"CX complaint about a faint smell of gas when not on inspected on the back & found connections on regulator not tight enoug as well on gas line tightened smell went away did a bubble test on all connections working fine CX still has a problem with both LF RF ignition took spreaders apart & back together started to ignigte need to replace them for not further issues; ordrng 2 W11344539 (flame spreader RF, LF)s and 1 LOOK (LOOK)"

cx complaint unit shut off while in a cycle. inspected unit and found lid is locked. removed console and found 121.7vac to control. console has no response. found water still in unit. tested drain pump and found 20 ohms. replace control and tested unit. unit now checks good.

"Installed parts, tested unit, unit working as designed."

"Cs unit is showing error code f8e4 overfill. Confirm complaint. Diagnostic is showing fae2 vent wax motor electrical problem. and f8e4 overfill switch. Found the float switch not securely connected . Confirmed wax motor is operating normally. Ran test cycle and each time it completed it good, no error codes came back and completed test cycle. Unit is now working properly."

Cx rescheduled the appt. I did not install the parts.; saved tckt

cx compalaint door seal coming off. installed new door gasket and heated and sealed. unit is niow good to go.

"Replaced both parts, all burners now heat and respond to touch. Unit checks good"

cx she opened the door to upper over and handle and door came apart.; ordrng 1 W10877562 (glass-door) and 1 W10575917 (spacer)

Cx stated unit tub is leaking and not washing inspected tested and verified cx complaint found tub defective and separating from drum. Ordering drum bellow clamps and shock absorbers just in case will need a second tech for repair cannot reached due to SO part. ; ordrng 1 W11287253 (Tub) and 1 W11314648 (Bellow) and 1 W11314649 (Clamp) and 1 W11266654 (Clamp) and 1 W11316766 (Shock absorber) and 1 LOOK (LOOK)

"Confirmed cx complaint unit not washing, going straight to done. Found F7E1 error code, tachometer not able to read basket speed. Ran high spin speed test, actuator pulls splutch into gear and speeds up then kicks F7E1 error code. Replaced actuator, issue persists. Service pointer W11632927 pertains to issue, ordering motor, harness, and capacitor. Found evidence of belt slipping, ordering tighter belt to stop squeeling noise on acceleration. Diagnostic mode would only engage one time, afterwards I could not get unit to respond in any function, no lock water or spin though unit was turning on. Ordering control as well.; ordrng 1 W11590868 (harness) and 1 WPW10006384 (drive belt) and 1 W11283592 (motor-drve) and 1 W11395618 (capacitor) and 1 W11567712 (control) and 1 W11481722 (Actuator EF VS) and 1 look, used 1 W11481722 (actuator) from stock"

"cx compliant unit is not draining. inspected unit and found unit was unplugged, plugged unit in and found 0 error codes. manually activated the drain and found drain pump sounds like something was in it. cleared water from unit with vacuum and removed drain pump and found a sock was stuck in pump. was able to removed sock and tested unit. unit now checks good. called TC (A152TS0NPL1) due to the unit just being out of warranty. whirlpool helped and unit is covered for repair."

"Cx refused service, thought diagnostic charge applied to labor. Unit is old, cx does not want to spend too much money repairing it."

Inspected the unit. Found that the cx is saying that the Dishes has white spots on the glasses. I then asked the cx if they are using Rinse Aid. Cx isn't using Rinse Aid. Advised that the cx uses Rinse Aid. Ran Service Diagnostics on the unit. No error codes solid white light. Checked the filter. Mold on filter and filter has to be cleaned. Showed the cx. Cx will start to clean the filter. Unit is working as Designed. Cx paid in full by Card.

CX complaint about a leak inspected no errors ran a cycle found that pipe on wall is backing up & causes to overflow & leak CX will need a plumber to take care of this issue

Customer compalint unit is not turning on the big burner. i found the element is good. Found the switch is bad. Ordering new switch. Owes 110 for labor. Schedule with office for friday.; ordrng 1 WPW10434452 (switch-inf 91.16)

This job was removed from my roster.; saved tckt

CX complaint unit opening by it self. I found the unit is cooling and freezing and doors are closing and feel tight.CX stated that the unit when is not cooling the door pops open.checked level & is unlevel towards the front just where door swings went to shim front wheels & CX refuse this states duct tape will hold door explained that gravity & floor unlevelness will cause doors to open he will get baby latches to fix issue

CX complaint about led for FC is out follow svc pointer W11460554F that talks about this & states to replace existing light with 3 point led used preid & working properly

CX complaint FRIDGE did not cool for 48HRS after last service. After that unit start to cool& make ice. Replaced evap fan damper again. Test in diagnostics control reals thermistors. Test damper & fans operate. Compressor runs. Reset power & compressor & fans runs > JJ

"Adjusted level of unit, condensor was vibrating heavily ..."

cx complaint units dispenser is pausing and doesnt work after the pause. got to unit and confirmed. it paused. i took filter out and put it back in and it would not pause again. it wasnt a pause like the water stoppped it was a pause as if the paddle was depressed. abrupt stop. inspected ice maker and is stuck in cycle. unit needs new ice maker. as far as the water issue. valve checks good. filter is new. water pressure and flow to unit is good. ordering control for the dispenser stopping. cx paid in full. please reschedule when part arrives.; ordrng 1 W11333076 (control) and 1 W10908391 (ice maker)

cx complaint is unit runs but no heat it seems and said vent is clear. units O-O-W and he knows. ran unit to test for feat. ran a few min and unit was cold. tested unit and found thermostate bad. replaced TCO kit and tested unit. unit now heats well and checks. job complete.

"CX Concern the unit getting too hot, found loose temp sensor, reseated and tested unit. Job complete"

Cx stated unit not spinning inspected tested and verified cx complaint found drive hub defective causing tub to wobble. Tried installing part from pre-id parts but found wash plate needs to be cut out in order to complete repair. Gave cx quote for repair cx accepted quote and paid in full by CC ordering wash plate to complete repair. Cannot resched due to SO part. ; ordrng 1 W10902814 (Wash plate)

"Cx complaint is unit is not cooling. inspected unit, all items in freezer compartment frozen solid, frost building on top of freezer door and top of freezer compartment. Removed air tower, found return vents clogged with ice. Opened refrigerator door, noticed large gap (approx. 3/8 in.) between frame and liner. Called tech line, sent pictures of gap to representative, tech line deemed unit unrepairable. Tech line provided file number, left file number with cx, told them Whirlpool will be contacting them,"

"CX complant. Control fell inside. Prior diagnosis found unit needs hardware kit . Installed control plate to control and then fastened control plate to hood canopy securing control in holes . Job completed, RB"

"CX complant. Control fell inside. Prior diagnosis found unit needs hardware kit . Installed control plate to control and then fastened control plate to hood canopy securing control in holes . Job completed, RB"

"CX complant. Control fell inside. Prior diagnosis found unit needs hardware kit . Installed control plate to control and then fastened control plate to hood canopy securing control in holes . Job completed, RB"

Cx Complaint is the unit is making noise. Inspected unit and ran unit got hot and starting making vibration noise pulled unit apart and found roller and idler are good vent assembly is making noising againt cabnet when it heats up adjust and tested unit is working properly.

Cx complaint unit is not working properly inspected unit found cx claims he got oven this way but racks were put in reversed and wedged in unable to removed used flathead to pop them out without bending reinstalled tested unit now functions normally

"cx complaint, no power. power cycled unit, ui powered back on. ui was doing some weird things. unable to verify cause, replaced main board and ui. tested unit, unit working as designed. job is complete."

cx complaint unit has dents in both sides insp unit conf cx comp found dent in right and left sides of cabinet cx has yet too move into home house is vacant; ordrng 1 W10677266 (cabinet)

"cx compalint water build up on top of freezer door showed me pic of the water build up and gasket is not sealing all the way it needs the seals behind gasket to keep it fluffy. grabbed seals from v/s installed and etsted door is sealing alot better now. unit is god; ordrng 2 w11159728 (seal SD V/S)s, used 2 w11159728 (seal SD V/S) from stock"

F4E3 Motor not running. Customer complaint unit is not washing. I tested the unit is not washing. motor error codes stored. I ran test not motor and is OL. Installed new motor unit is working. Custoemr did not have closing i took a picture of the deed. The unit is under warranty.